Part XI – Catalyst 1900 Switch The Catalyst 1900 Switch can be configured b

[admin]

Part XI – Catalyst 1900 Switch
 
The Catalyst 1900 Switch can be configured by a menu system, the Command Line Interface (CLI) or the Virtual Switch Manager (VSM) through a
web browser once the IP address has been set.  By pressing K at the first menu, you can access the CLI. The switch can table up to 1024 MAC
addresses.  The 1900 can use Store-and-Forward or FragmentFree (default) switching modes.
 
enable/disable: used to enter or exit the privileged mode
 
General commands entered in the “#” mode:
show version: displays basic IOS and switch information.
show ip: used to see the IP address settings on the switch, along with subnet, default gateway, domain name, and other parameters.
ping address: used to test connectivity from the switch.  telnet or traceroute can only be used from a router.
delete nvram/vtp: erases the startup-config of a switch or VTP information.  You cannot see the content of the startup-config on a switch, nor copy
to or from it.  Every changes made to the configuration is made to the NVRAM file immediately.
sh mac-address-table: displays the MAC address table.
clear mac-address-table dynamic/permanent/restricted: clears the address in the MAC address table that match the option chosen.
sh port system: displays information about switching type.  Fragment-Free is the default switching mode.
sh vlan [number]: displays the VLAN information and port association about all VLANs or only the number VLAN.
sh vlan-membership: displays the VLAN information for all the interfaces.
sh trunk a/b [allowed-vlans/joined-vlans/joining-vlans/prune-eligible]: displays trunk information (port 26=A, 27=B).
copy tftp://hostaddress/IOSfilename opcode: used to update the IOS on the switch from a tftp server.
copy nvram tftp://hostaddress/filename: used to backup the startup-config file.
copy tftp://hostaddress/filename nvram: used to restore the startup-config file.
show cdp: displays cdp information.
 
config terminal: use to enter the terminal configuration
 
Commands entered in the “(config)#” mode:
hostname name: used to define a hostname that is locally significant only.
enable password level number password: used to set user and enable mode passwords (by setting number to either 1 or 15 respectively).  Password
must be between 4 and 8 characters and is not case sensitive.
en secret password : used to set the enable password using the encryption service.  This will override the non-secure password if set.
ip (address ipaddress subnetmask)/(default-gateway gatewayaddress): used to set the IP address and subnet mask, or the gateway.
mac-address-table aging-time time: sets the aging time of dynamic addresses in .
mac-address-table permanent address destinterface: used to define permanent addresses.
mac-address-table restricted static address destinterface sourceinterface: used to define restricted addresses.
switching-mode fragment-free/store-and-forward: used to set the switching mode.
vlan number name name: defines VLANs.  number is 1-1000.  VLAN 1 is the default VLAN and all ports are associated to it. Maximum of 64
VLANs on a switch.
vtp server/client/(domain name)/(password pw)/(pruning en/dis)/transparent/trap : configures VLAN Trunk Protocol .  Pruning is enabled on
the whole domain if it is enabled on a server.
cdp advertise-v2/(holdtime/timer seconds): used to configure CDP (Cisco Discovery Protocol) information.
 
interface (ethernet 0/1-25)/(fastethernet 0/26-27) : the Ethernet interfaces are numbered 1-24, plus the serial port for AUI at the back, and the
FastEthernet uplink ports are numbered 26-27.  There is only one slot, slot 0.
 
Commands entered in the “(config-if)#” or “(config-subif)#” mode:
duplex auto/full/full-flow-control/half : used to change the duplex settings on a given port. auto is the default for 100BaseTX ports, and half is the
default for 10BaseTX ports.
desc ription name: used to define a description for the interface.  Name must have underscores rather than spaces.  show run and show int 0/n will
both show the descriptions set.
port secure max-mac-count number: will only allow number MAC addresses on the interface, and they will be permanent.
vlan-membership static/dynamic number:  assigns a port to a VLAN.    One VLAN per port unless trunking is used.
trunk auto/desirable/nonegotiate/on/off: used on the FastEthernet ports to enable trunking.  All VLANs are allowed on the trunk by default.
no trunk-vlan number: to clear VLAN number from being trunked through this interface.
encapsulation isl vlan_number: in each subinterface of a trunk port, in order to support VLAN trunking.